Page 1 of 1

seagate ST2000LM007 -SBK2 diagonstic port locked

Posted: 25.04.17, 10:46
by sigmaalv
i have a model seagate ST2000LM007 mobile hdd. its shows id and correct size. but not able to read any sector. i can access terminal. when i press cntrl+L its shows " diagonstic port locked". please see startup log below

Boot 0x80M
Rst 0x80MSrv DETCR init 0x0000
EDAC Value = 0000F018E59FF018
EDAC Value = 0000F018E59FF018
EDAC Value = 0000F018E59FF018
EDAC Value = 0000F018E59FF018
(P) SATA Reset

RAW OFF
PASS
EDAC Value = 00000000FFFFF844
EDAC Value = 00000000FFFFF844
EDAC Value = 00000000FFFFF844
EDAC Value = 00000000FFFFF844
EDAC Value = 00000000FFFFF844
EDAC Value = 00000000FFFFF844
EDAC Value = 00000000FFFFF844
EDAC Value = 00000000FFFFF844
(DOS Table) Worst Count: 0000100C At SU: 00004C33 NT: 00000002 OT: 00000007
MCMT table is corrupted
MCMT table is corrupted
Intel 6G->3G
Send Status: COMRESET seen
CSpd= 3Gbps
DSC
MCMT table is corrupted
MCMT table is corrupted
ASCII Diag mode

F3 T>
ASCII Diag mode

F3 T>
ASCII Diag mode

F3 T>
ASCII Diag mode

when press cntrl+L

F3 T> "diagonstic port locked"




********************
please check below log while reading ROM

Selected family......................... : 00, F3 Arch (common)
Model by ID............................. : ST2000LM007-1R8174

Tech Key...

Requesting FW Pkg ver ........ RT0898.SDM2.CC4618.SBK2


Detecting Phys Sct Size...
Result.................................. : Error
Error obtaining Phys Sect Size!
GetModePage 0x3 err! Tech state 0x72, 0x07200200
Terminal : error detecting HDD terminal baud rate


Test : Read ROM

Reading ROM to profile folder
Folder: E:\PC3000-E\!Profiles\SgF3\F3 Arch (common)\ST2000LM007-1R8174-SBK2-WCC2NJSB\Data\ROM\
File : ROM.bin
Error : DT ID 15 is not found!
Result.................................. : Error


Test : Read ROM

Reading ROM to profile folder
Folder: E:\PC3000-E\!Profiles\SgF3\F3 Arch (common)\ST2000LM007-1R8174-SBK2-WCC2NJSB\Data\ROM\
File : ROM.bin

Switching HDD power supply OFF

Switching HDD power supply ON
Error : Terminal : reply timeout error
Result.................................. : Error
WARNING!
In Boot Code mode HDD have shortened commands set!
For full-mode work via utility you have to switch HDD power supply OFF/ON!


any help. i get many of this drives

Re: seagate ST2000LM007 -SBK2 diagonstic port locked

Posted: 25.04.17, 14:35
by Amarbir[CDR-Labs]
Sir ,
Model Not Supported In PC3K Yet

Re: seagate ST2000LM007 -SBK2 diagonstic port locked

Posted: 10.01.18, 11:34
by vijayan
EDAC Value = 0000F018E59FF018


HDD ID Display But LBA: 0

Solution :
Attachments
Capture.JPG
Capture.JPG (4.13 KiB) Viewed 7437 times

Re: seagate ST2000LM007 -SBK2 diagonstic port locked

Posted: 10.01.18, 11:56
by AJ2008
I would ignore EDAC values but instead focus on 0LBA which is symptoms of a translator issue. You can unlock these models on PC3000, but there is a risk of data loss when clearing translator and associated MC data, so ensure a full SA backup is made before any attempts to resolve the translator.

Re: seagate ST2000LM007 -SBK2 diagonstic port locked

Posted: 14.01.18, 12:11
by Amarbir[CDR-Labs]
Well ,
This Can Be solved Now

Re: seagate ST2000LM007 -SBK2 diagonstic port locked

Posted: 02.05.19, 21:32
by vijayan
Case Solved Ts team