WDC WD40NMZW-11GX6S1

Moderator: Maxim_TS


redlabs
New user
Posts: 50
Joined: 02.07.13
Reputation: 2 / (20)

WDC WD40NMZW-11GX6S1

Postby redlabs » 01.09.19, 09:59

Dear Friends ,

This spy glass i received with little bit noise ,I have done all solve slow reading process ,But SPT not reading when block 02 module SPT reading normally ,

one allocation table................... : Ok
SA SPT.................................. : 2140

ROM:
Read ROM................................ : Ok
ROM Data size........................... : 512 Kb
Flash ROM dir reading................... : Ok
Flash ROM dir reading (Ext)............. : Ok (Active)
Modules directory address............... : 809 245
SA regions address...................... : by default
SA regions address (RAM)................ : by default
Module 02 access........................ : Blocked
SA Translator loading................... : Ok
SA defects assigned..................... : 1

ROM Modules:
ROM version............................. : 02.1PR
ROM F/W version......................... : 0002001P
Overlay F/W version..................... : 02.1QR
Servo F/W version....................... : F1.3R

Heads configuration..................... : by map
Heads number............................ : 10
Heads number in use..................... : 10
Switched off heads...................... : No
Heads map............................... : 0,1,2,3,4,5,6,7,8,9

Service area:
SA dir reading (ID)..................... : Ok
SA Access............................... : Copy 0,Copy 1

Configuration reading................... : Ok
Master Password......................... : has not been set
User Password........................... : has not been set

Module checking 02 (Configuration (HDD ID) (Pasport Sequrity Block))
Module 02............................... : Ok


any one suggest to how to read ID


Maxim_TS
Site Admin
Posts: 291
Joined: 27.03.13
Reputation: 15 / (149)

Re: WDC WD40NMZW-11GX6S1

Postby Maxim_TS » 05.09.19, 16:22

redlabs, try to block SA access in ROM, restart the drive and utility, upload Dir and loader from backup, then perform Warm reset from the right toolbar, then restart the utility.
Let us know if it helped.
With best regards
ACELab technical support
ts.acelaboratory.com
blog.acelaboratory.com


redlabs
New user
Posts: 50
Joined: 02.07.13
Reputation: 2 / (20)

Re: WDC WD40NMZW-11GX6S1

Postby redlabs » 09.09.19, 12:05

Same result , I am not able to the read ID


Maxim_TS
Site Admin
Posts: 291
Joined: 27.03.13
Reputation: 15 / (149)

Re: WDC WD40NMZW-11GX6S1

Postby Maxim_TS » 10.09.19, 17:49

redlabs wrote:Source of the post Same result , I am not able to the read ID

write 32 from the same ROM FW version 0002001P good donor backup, and restart the drive.
With best regards
ACELab technical support
ts.acelaboratory.com
blog.acelaboratory.com


redlabs
New user
Posts: 50
Joined: 02.07.13
Reputation: 2 / (20)

Re: WDC WD40NMZW-11GX6S1

Postby redlabs » 15.09.19, 11:32

i block 02 module in rom and i allow access on Ram and i give soft reset ,its read id and i un tick SED lock i got full access of HDD

Thanks
max


Return to “WD Marvell”

Who is online

Users browsing this forum: No registered users and 3 guests